Jeppesen’s Airframe Oral & Practical (O&P) Practice Exam

These questions are part of the practice quiz. Start practicing

• What is the shared role of trim tabs in aircraft?
• What is the first step in removing a solid-shank rivet?
• Which of the following is a consequence of proper tire inflation?
• What methods are commonly used to remove rain from an aircraft windshield?
• What happens to the gears in a gear-type pump during operation?
• What identification marking is found on the selvage edge of aircraft fabric?
• Where is surface tape commonly used in aircraft fabric covering?
• Aircraft covering fabrics are made from which two types of materials?
• Is compression wood suitable for structural repairs in aircraft?
• What effect can a malfunctioning anti-skid system have during landing?
• What are the two primary uses for plywood in aircraft construction?
• In what way is a thermocouple fire warning system different from a thermal switch system?
• What potential issue arises if open-assembly time is not adequately considered?
• What type of guidance does the glideslope beam provide?
• What is the purpose of a Mach airspeed warning system?
• What are some methods used to test the condition of aircraft fabric?
• What is the first step in determining the total length of a solid rivet for installation?
• What warning system is suggested when a nickel-cadmium battery is installed in an aircraft?
• Where on the aircraft would you expect to find a DME antenna?
• Which method is NOT commonly used for forming sheet metal?
• For what reason do aircraft crews monitor fuel temperatures?
• What is a possible effect of kinks and sharp bends in the sensing element of a fire warning system?
• What should be done to corners where two bends intersect to prevent cracking?
• How is the output voltage of an alternator controlled?
• How can the operation of a photoelectric smoke detector be tested?
• What is the primary purpose of the FAA-PMA stamp on aircraft fabric?
• How should coaxial cable be routed from an antenna to a receiver?
• What is the important step before making a cold-patch repair to a deicer boot?
• Which auxiliary control can also be used to improve stability at speed?
• What information is used to perform a static check on a manifold pressure gauge?
• Which component typically alerts pilots to low fuel levels?
• How does an air-cycle system produce cool air?
• What can happen if a rivet set does not fit the rivet properly?
• How should the edges of drainage and inspection holes be reinforced?
• What factors should be considered when determining the size for a particular application?
• What is one advantage of a single-point fueling system?
• Why is welding magnesium considered a serious safety hazard?
• Why is the proper clamping pressure vital for a glue joint?
• Where are control cables most likely to wear or break?
• What tool would you use to determine the size of an unmarked wire?
• How is a takeoff configuration warning typically different from a landing gear warning?
• What distinguishes a vapor-cycle cooling system from an air-cycle system?
• What are the primary components of an air-cycle cooling system?
• Why do some pneumatic deicer boot systems include an electrically operated timer?
• What is the purpose of the selvage edge on a roll of fabric?
• What power sources are used to operate aircraft windshield wipers?
• Why do multi-engine airplanes utilize fuel crossfeed systems?
• How are the pilots' nose wheel steering commands transmitted to the steering control unit of a large aircraft?
• Why is a fuel jettison system typically divided into two separate systems?
• When an oxyacetylene torch is extinguished, which valve should be turned off first?
• Which of these controls is primarily responsible for roll control?
• With which gas should a landing gear shock strut be inflated?
• Which type of paint is commonly used on aircraft?
• What defines a positive-displacement air compressor?
• How would you identify a specific wire in a wire bundle?
• Why is it essential to have accurate range markings on aircraft instruments?
• How are A, B, D, AD, and DD rivets marked?
• Why is overheat protection necessary for anti-ice systems that utilize turbine engine bleed air?
• Which of the following statements about thermocouple systems is true?
• What alerting method is usually employed in jet transports to signal that cabin doors are not closed properly?
• What is a problem associated with the in-flight operation of aircraft windshield wipers?
• What type of flame is utilized for torch brazing of silver soldering?
• In addition to width and height, how should a rivet be assessed during installation?
• What are some indication errors that can occur in altimeters?
• What is the proper length for a bonded jumper?
• Which of the following can be a source of ventilating air in a combustion heater?
• What is the main function of a restrictor in a pneumatic system?
• What is the main purpose of the secondary heat exchanger in an air-cycle system?
• What happens if the radius of a rivet set is too large?
• What unit in an anti-skid system generates the anti-skid warning signal?
• What is one purpose of internal baffles within fuel tanks?
• What component can act to restrict airflow in a pneumatic system?
• What is the principal advantage of the envelope method for covering wings?
• Which method can be used to monitor the signal output during an ELT test?
• During which phase of operation should the integrity of the fuel system be most frequently checked?
• What type of material is used in a kidde system to change resistance with temperature?
• What is a common method for controlling expansion when welding a joint?
• Why is it critical to control the weight of a bucking bar in sheet metal work?
• Which regulation governs the application of registration numbers on aircraft in the U.S.?
• What is an important factor to check in fuel system maintenance?
• What type of switches are used in a thermal switch fire detection system?
• Which condition does NOT typically activate the takeoff configuration warning system?
• Which of the following is NOT a common cause of delamination in composite structures?
• What does DME stand for?
• What are the three types of accumulators used in hydraulic systems?
• What is the primary function of ventilating air in a combustion heater?
• What are the two types of organic fibers commonly used for covering aircraft?
• What do the terms warp, weft, and bias refer to in fabric?
• Before inspecting a brake system for leaks, what must be done?
• What overall function does the crew alert system provide during flight?
• What makes butyrate dope safer than nitrate dope?
• What must be done after an oxygen system has been opened to the atmosphere?
• Which action occurs last during the installation of self-plugging rivets?
• What does an anti-skid warning indication signify?
• What condition can lead to "orange-peel" in a paint finish?
• At what percentage of its original strength is fabric considered unairworthy?
• What is the function of compensating magnets in a compass?
• What are the basic components of a radio communication system?
• What is the outcome of not properly preparing a surface before painting?
• How is cabin pressure primarily controlled in an aircraft?
• What is the purpose of a fairlead in aircraft systems?
• What effect does spraying rain repellent on a dry windshield have?
• How does a pneumatic rain removal system operate?
• How can one increase the heat transferred from a soldering iron tip to the work?
• Which components are typically included in an airborne VOR navigation system?
• What safety precaution must be taken when removing a wheel from an axle?
• What action is needed if there is a discrepancy in the range markings on an instrument?
• Which method is primarily used for changing the shape of sheet metal?
• Which of the following are types of brake actuating systems?
• What frequency range is used by modern voice communications systems?
• What are the basic components of an autopilot system?
• What is a characteristic of synthetic enamel paints used in aircraft coatings?
• Which type of synthetic fiber is known for its resistance to moisture and mildew?
• What are the three principal types of welding?
• What should be done when making bonding or grounding connections between dissimilar materials?
• How is thrust produced by the tail rotor typically controlled?
• What are the two types of fuel cells used in aircraft?
• How will the switches be connected if an aircraft with retractable landing gear has only one green light indicating the gear is down and locked?
• Which aircraft instruments are typically connected to the pitot-static system?
• Which of the following is an appropriate method to purge moisture from an oxygen system?
• Which of the following safety precautions is critical when servicing oxygen systems?
• Where are carbon monoxide detectors typically installed in an aircraft?
• What could cause an AC electric motor to run too slowly?
• What is the purpose of reinforcing tape in aircraft fabric covering?
• What occurs to the stem of a self-plugging (friction lock) rivet during installation?
• What type of compressor is a roots blower?
• What systems are usually utilized to activate the landing gear warning system?
• Who determines the type of fabric used for fabric-covered aircraft?
• What references should be consulted for proper range markings for aircraft instruments?
• What is the fundamental difference in tools required for CherryLOCK and CherryMAX rivets?
• What is one consequence of using a thinner that evaporates too quickly?
• What is the purpose of shielding an arc weld with an inert gas?
• Engine-driven pumps deliver fluid in what forms?
• What is a tie-off knot used for in sewing?
• Which of these is a feature of secondary flight controls?
• Which method is used to pressurize a hydraulic reservoir?
• What is the major type of damage to aluminum structures that is caused by exposure to the weather?
• What could cause an AC electric motor to run too fast?
• What types of issues can arise with electrically heated windshields?
• What mechanism ensures that a nose wheel is not turned as it retracts into the wheelwell?
• What part of an aircraft is identified by a white navigation light?
• What are the primary sources of pneumatic power in aircraft?
• Where are anti-tear strips typically used?
• What is the power source for an ELT?
• Which components are part of a vapor-cycle system?
• What is the potential consequence of failing to maintain cleanliness around oxygen systems?
• What occurs to excess pressure within a pneumatic system?
• What methods are commonly used to attach a deicer boot to the aircraft's wing and tail surfaces?
• When using a growler, what indicates that a short exists between an armature segment?
• What is a key characteristic of fiberglass as a fabric type for aircraft?
• What are the common methods of inflating pneumatic deicer boots?
• Which paint system may be used with epoxy topcoats?
• What are the two types of dope used for fabric finishes?
• What is the purpose of a torque link on an oleo strut?
• To effectively insert a tight inner sleeve into a repair, what should be done to the materials involved?
• What role does a primary heat exchanger play in an air-cycle system?
• What is the first safety precaution that must be taken before disassembling an accumulator?
• When will a landing gear aural warning typically sound?
• What is the function of the servos in an autopilot system?
• What does the reinforcement of fabric edges prevent?
• How does a carbon monoxide detector indicate the presence of the gas?
• What is a critical reason for considering the open-assembly time when gluing wooden structures?
• What should be considered when selecting the size of a rivet in relation to rivet spacing?
• At what time(s) is a test of an installed ELT permitted?
• Where would you find information on acceptable limits of windshield delamination?
• What is the effect of inadequate penetration on a weld?
• What device supplements the pump output during periods of high demand in hydraulic systems?
• When inspecting wood structures, why is it important to note stains and discolored areas?
• How can one determine correct stitching spacing if the original is unknown?
• At what times should a gear retraction check be performed?
• What is a key benefit of using bladder-type fuel cells?
• What unit is responsible for regulating the position of the outflow valve?
• Why must the beveled cut be accurate on both pieces of wood being repaired with a scarfed joint?
• Why are two antennas typically required for an ILS system?
• What conditions can activate a takeoff configuration warning system in jet transport aircraft?
• What is the recommended included angle for a drill bit used for drilling composites?
• Which advantage is associated with gas shielded arc welding?
• What might happen if excess moisture is left in a pneumatic system?
• What is a characteristic appearance of a blushing paint finish?
• Under which situation are splices to a wood spar prohibited?
• Under what conditions must a switch be derated from its nominal rating?
• What action should be taken if a fuel system component is damaged during maintenance?
• What should be done when drilling a hole in Plexiglas to avoid damage during breakthrough?
• When replacing a hydraulic unit, what is a key precaution to prevent system contamination?
• What must be done to a heat-treated aluminum part once welded repairs are finished?
• What type of circuit breaker may not be used in an aircraft?
• Which aircraft systems are commonly operated pneumatically?
• When is a check of the landing gear warning system typically performed?
• What quantity is accurately measured by a capacitance-type fuel quantity indicating system?
• What is the primary function of a pressure-demand oxygen system?
• What tool is used to check a motor or generator armature for shorts and opens under load conditions?
• After completing a welding project, what is a vital action to ensure safety?
• Which of the following is a characteristic of engine bleed air in hydraulic systems?
• What finishing defect is likely if the paint room temperature is too warm?
• Which of these is NOT a common type of high lift device?
• What prevents air from leaking out between the two halves of a split wheel assembly?
• What common issue is caused by inadequate surface preparation or overly thick paint application?
• Which element is commonly activated during low-speed flight for better control?
• What technique can facilitate inserting a tight-fitting inner sleeve into a tubular repair?
• What conditions should a mechanic look for during a regular inspection of the exposed piston section of a landing gear?
• What is the preferred method for welding aluminum?
• What happens to the air after it is expanded across the turbine in an air-cycle cooling system?
• Why are fusible plugs installed on some aircraft wheels?
• What does a compass require to function properly in an aircraft?
• What is the primary purpose of an annunciator system in an aircraft?
• What is the main function of an anti-skid system?
• What type of wood should be used when splicing plywood webs?
• Which method enhances the strength of a glue joint during the curing process?
• What type of glue requires careful inspection in older wooden aircraft due to deterioration?
• What is the primary function of rotorcraft cyclic pitch control?
• Why is it important to use the correct type of paint on aircraft?
• If replacing a 2024 rivet with a 2117 rivet, how do you determine the appropriate size?
• What is the primary function of a pressure relief valve in a hydraulic system?
• What is the primary effect of using dope over paint or enamel?
• What material is often bonded to the core in a honeycomb structure?
• What is the main purpose of a joggle in aircraft construction?
• What is the basic function of a water separator?
• What are the at least three positions of the fuel selector valve in a multi-engine aircraft?
• Prior to making a continuity check, what must be done to an electrical circuit?
• What is the fate of the hot air used by a thermal anti-ice system after it has heated the aircraft surface?
• What may happen to paint if exposed to excessive moisture immediately after application?
• What is the primary purpose of painting in aerospace applications?
• How is a bonded honeycomb structure constructed?
• What type of joint is commonly used to splice a solid or rectangular wood spar?
• What is the primary source of pressurization air in most jet aircraft?
• How does a stall warning system typically alert pilots in small aircraft?
• What is the purpose of a debooster in brake systems?
• Which of the following describes the three axes of an airplane?
• What is the name of the effect that causes a gyro to respond at a point 90 degrees further in the direction of rotation?
• Which factors are essential in determining the setback for bending sheet metal?
• What is the purpose of a spring tab?
• What condition would cause the bypass valve in a hydraulic filter to open?
• Which of the following is NOT a source used to develop hydraulic pressure?
• Which component in the photoelectric smoke detector is responsible for conducting electricity?
• What is the basic operating concept of a synchro-type remote indicating system?
• What are some alternative names for a single-point fueling system?
• What component prevents engine damage if an engine-driven hydraulic pump seizes?
• Which welding method is least likely to cause buckling or warping of thin metal sheets?
• Why might fuel quantity gauges be essential in flying conditions?
• Why should wood pieces be kept in the same room for at least 24 hours before joining?
• How should the strength requirements for fabric used to re-cover an aircraft be determined?
• What is the minimum spacing required between rivets for protruding head rivets?
• Can a section of wood with a hard knot be used in aircraft construction?
• What method is used to prevent cracks when dimpling magnesium or hard sheet metals?
• What is the importance of a clogged filter element in a hydraulic system?
• What must be done with a damaged area in a bonded honeycomb structure before repairs?
• Why would it be necessary to analyze an electrical system before increasing the load on the system?
• What is the operating principle of a continuous-flow oxygen system?
• What are the characteristics of fabric that is suitable for aircraft covering?
• What is the special requirement for the type of oxygen used in an aircraft system?
• Why do transport category aircraft have a master caution and warning system?
• What visual indication confirms that the landing gear is in the correct position?
• What is one method for repairing a dented steel tube cluster joint?
• What should be done to a structure before covering it with doped fabric after inspection?
• Which of the following describes the components of a kidde continuous loop fire detection system?
• What are the sensing elements of an auto system?
• Exposure to which of the following factors can cause crazing in transparent plastic windows?
• What procedure is employed to keep deicer boots flat against the airfoil surface during flight?
• During which scenario should a pressure check for brake systems be performed?
• What is the primary function of the gas in a Lindberg fire detection system?
• Which factors influence the amount of heat delivered by a gas welding torch?
• Can the functionality of an electrically heated pitot-tube be verified using the aircraft's ammeter?
• Why might an aircraft require a jettison system beyond the maximum landing weight?
• How can a mechanic decide whether to dimple or drill a flush rivet?
• What is the function of the in-transit light associated with an electrically operated fuel tank shutoff valve?
• What safety precautions should be completed after finishing a gas welding project?
• How do magnetic fields from electrical equipment affect a magnetic compass?
• What is a potential cause of a landing gear aural warning?
• Which of the following is NOT one of the three types of glue used in modern aircraft construction?
• What is the main concern when using tools inside a pitot-static system?
• Which four types of fuel quantity gauging systems are commonly used?
• Which method can be used to bleed brakes?
• What are the sources of power for driving a gyroscopic turn indicator?
• Which type of wood is NOT commonly used in aircraft construction?
• What is the shape and location of a transponder antenna?
• At what point in a circuit should the protective device be located?
• What can be the outcome of exceeding the maximum pressure in a hydraulic system?
• What instruments are used to monitor electrical system loads?
• What is the purpose of fuel jettison systems in aircraft?
• What should be done to mitigate risks when working with aerosol sprays?
• Which of the following is NOT a type of self-plugging mechanical lock rivet?
• How is a fuel tank tested for leaks after a repair?
• Circuit breakers are designed to open before what condition occurs?
• How does a gear-type pump operate?
• What is the general purpose of auxiliary flight controls?
• What does a balance trim tab do?
• What function do overheat sensors serve in a thermal anti-ice system operated by engine bleed air?
• What makes electronic (capacitance-type) fuel quantity indicating systems more accurate?
• What is the function of a cable tension regulator?
• What is the primary function of a vortex generator?
• What is the effect of adding a top mush drier to the paint?
• What controls the temperature in a thermal anti-icing system?
• What are the three most common methods of applying paint?
• What does the term "ADF" stand for?
• How would one determine if the batteries in an ELT need recharging or replacement?
• When repairing an all-metal aircraft, which factor is crucial to consider in selecting metal?
• What are the visible signs of excessive heating on a wheel bearing?
• What is one function of applying clamping force during the adhesive process?
• Which of the following factors affects the strength requirements of aircraft fabric?
• What is a common visual indication of a system that requires immediate crew attention?
• Name several types of electrical devices that would be considered intermittent loads on an electrical system.
• What characteristic of large washers helps in reducing damage to wooden structures?
• What is the preferred method of welding magnesium?
• When inspecting wooden structures, what do discolorations typically indicate?
• What are the sources of heat for a thermal anti-icing system?
• Which of the following valves should not be turned off during the extinguishing process of an oxyacetylene torch?
• Why should you avoid cleaning obstructions from the sensing holes in a pitot-static system with a tool?
• Why are lightweight steel bushings used in wooden structures?
• What could potentially happen if the torque link on an oleo strut fails?
• Describe the characteristics of a scarf joint.
• Which statement best describes the definition of bias in fabric?
• What colors denote mineral-based and phosphate-ester hydraulic fluids?
• Which type of accumulators is commonly used for storing hydraulic energy?
• Which landing gear positions must regulations indicate?
• What should be avoided entirely when servicing oxygen systems?
• What are the most common sources of power used to extend and retract landing gear?
• What is the primary purpose of using zinc-chromate or wash primers?
• Which condition is likely caused by tire under-inflation?
• What is the maximum number of terminal lugs that can be placed on a single terminal strip stud?
• Which warning indicates that a pilot may encounter a stall?
• What three mechanical methods can actuate flight control systems?
• How can hydraulic pressure be described in terms of control within the system?
• What materials form the bases of the three types of hydraulic fluids?
• Which devices provide warnings for a retractable landing gear system?
• How often must an ATC transponder system be certified?
• Why should a control surface be locked when an aircraft is parked?
• What is typically used between the fabric and rib stitching to ensure proper adherence?
• Why should you wait after fueling an aircraft before checking the fuel sumps?
• What is the effect of exposing lacquers, oil-based paint, plastic resins, and vinyl compounds to phosphate-ester-based hydraulic fluid?
• What type of defect in a bonded honeycomb structure can be repaired using the potted repair method?
• At what point do electric motors draw the most current?
• Why is periodic purging of a pneumatic system necessary?
• Which characteristic of internal baffles helps with fuel management?
• What does the term "wet wing" refer to?
• What characteristic of fuel systems helps prevent contamination during refueling?
• Beyond aesthetics, what is a reason for touching up painted surfaces on aircraft?
• What are the two critical calculations involved in bending sheet metal?
• In brake systems, what can be the result of high hydraulic pressure?
• What is the purpose of regulators in a hydraulic system?
• How does a photoelectric smoke detector generate a warning of a possible fire?
• What is the purpose of installing lightening holes in sheet metal?
• What should be included in the preparation for repairing a plywood structure?
• What type of fuel system is most commonly found on older aircraft?
• What characteristic distinguishes AD rivets from other rivets?
• What typically causes dope to blush?
• What precaution must be taken when welding titanium?
• How is the nose wheel steering mechanism usually actuated on a small aircraft?
• What is the function of an anti-ice overheat light in airplanes equipped with bleed air anti-icing?
• How can a soft flame be achieved without reducing the torch's heat output?
• What is the relationship between the inside diameter of a conduit and the outside diameter of the wire bundle inside it?
• What is the purpose of flux in brazing and silver soldering?
• What two aspects should be inspected in a magnetic compass?
• What are drip gauges and sight gauges used for in aviation?
• What operating parameter does a tachometer indicate?
• Which of the following is NOT a defect found in wood?
• How does rotorcraft collective pitch control affect rotor blades?
• What can occur if a motor is overloaded?
• How does a servo trim tab function?
• What maintenance function most significantly affects tire service life?
• Which type of cabin air compressor uses airflow to compress air?
• During plywood repairs, which process is essential for ensuring joint strength?
• How are the detector units in a double-loop Fenwal system wired?
• What is the purpose of a bonding jumper from the radio shock mount to the airframe?
• What would trigger an anti-skid warning during landing?
• Which components need protection when using paint stripper on an aircraft?
• Why is choosing the proper size and weight of a bucking bar essential in sheet metal riveting?
• When is oxygen supplied at higher than atmospheric pressure in a pressure-demand system?
• Which reference should be consulted to determine if a control surface needs to be checked and/or rebalanced after painting?
• What effect can cold temperatures have on the paint application process?
• What should be done with old gaskets and seals when replacing components in the fuel system?
• Which type of cabin air compressor is considered positive-displacement?
• What is an acceptable method to repair elongated bolt holes in a wooden wing spar?
• In what situation might a fuel jettison system be needed on a small aircraft?
• Which materials are used in facings and core materials for bonded honeycomb structures?
• What is a likely cause if spray painting results in a dry and rough surface?
• What is the name of the unit that prevents a nose wheel from vibrating or oscillating?
• How is fuel weight supported in bladder-type fuel cells?
• Which mechanism compensates for the torque produced by a helicopter's main rotor?
• What is the function of the expansion turbine in an air-cycle cooling system?
• What type of pressure application tool can be used in glue joint construction?
• What is a common type of patch used for repairing plywood skin?
• Which of the following is a key feature of an effective fuel jettison system?
• What tools are typically used to check control surface travel?
• Which type of fiber is commonly used in synthetic covering for aircraft?
• Which type of stress most commonly causes rivet failure?
• What is the purpose of incorporating an oil separator in some deicer boot systems?
• What test is required after components in a pitot-static system have been replaced?
• What type of patch should be used for small holes in thin plywood skin if the skin is less than 1/10th inch thick?
• What are the three primary flight controls of an aircraft?
• What health and safety measures should be taken when using toxic solvents in finishing systems?
• What is the purpose of large surface area washers in wooden structures?
• What is the minimum curing temperature recommended for joining wood with adhesives?
• What is an indicator of poor electrical connections in a circuit?
• Which of the following is NOT a method used on reciprocating-engine aircraft to provide heated cabin air?
• What type of light signals that a non-critical system needs attention?
• Who is authorized to apply the range marking to an instrument dial face?
• What are the dimensions of a properly formed rivet head?
• Which of the following methods can be used to apply pressure to glue joints?
• Which of the following are common types of machine-sewed seams?
• Which type of temperature sensing system is typically used for measuring turbine engine exhaust gas temperature?
• What is the purpose of a slippage mark on an instrument glass?
• Why do turbine-engine aircraft have fuel temperature indicating systems?
• What is the primary function of VOR equipment?
• What is the maximum number of splices allowed for a single wood spar?
• What is the outcome of ignoring proper caps or plugs after disconnecting hydraulic lines?
• In aircraft construction, why is plywood preferred over solid wood?
• What is the minimum edge distance for a single row of protruding head rivets?
• What is the primary signal source in an electrical resistance-type temperature indicating system?
• Which instrument can be used to check a manifold pressure gauge for accurate indications?
• How is a pilot informed when an anti-skid system switches to a manual braking system?
• What are the effects of under-inflation on aircraft tires?
• What is one potential effect of arcing on an electrically heated windshield?
• Can a fuel system develop a leak without visible evidence, and how?
• What indicates that the landing gear is down and locked?
• What are two types of smoke detection systems used in aircraft?
• What color are the navigation lights on the wingtips?
• What should be placed between a plywood patch and the pressure plate to prevent sticking if glue is extruded?
• Why is oil added to the refrigerant in a vapor-cycle air conditioning system?
• Where can you typically find procedures for checking and adjusting landing gear switches?
• What might a malfunction in the landing gear system cause?
• What typically indicates the need for a dimple instead of a countersink?
• Which fire detection system involves a pressure switch activated by gas release?
• How are thermal switches typically connected in relation to each other?
• Which flight control is used to manage pitch?
• What information is necessary to utilize a cable rigging chart?
• What does a yellow arc indicate on an aircraft instrument?